Adress:Weihai Road, Jing'an District, Shanghai

s235j2 steel properties

Contact us

S235J2 steel - Steel grades, Properties and Global Standards

Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. S235J2 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc.

Reply

S235J2|S235J2 STEEL PLATE--YUSHENG STEEL

EN10025 _ 2 S235J2 steel plate is mainly used in structural projects and tanks,it is equal to our Chinese . standard steel grade Q235D.They are both done low temperature impact test at minus 20 centi degree. Sometimes S235J2 would be used to built containers which can bear low temperature sea water.

Reply

S235J2 steel

Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. S235J2 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc.

Reply

S235J2 - BEBON steel

S235J2 steel plate is the Non-alloy structural steels. S235J2 steel’s Mechanical properties is Yield strength more than 225MPa, tensile strength 340-510MPa, Elongation is 24%. Ultrasonic Test shall be carried out according to EN10025_1.For the impacting test,it indicates by J2.

Reply

EN 1.0117 (S235J2) Non-Alloy Steel :MakeItFrom

S235J2 is the EN chemical designation. It has a moderately low tensile strength and a moderately high ductility among wrought carbon or non-alloy steels. The graph bars on the material properties cards below compare EN 1.0117 steel towrought carbon or non-alloy steels (top), all iron alloys (middle), and the entire database (bottom).

Reply

EN 10025-2 S235J2 high strength structural steel plate

S235J2 Characteristic. S235J2 is a low carbon, high tensile strength structural steel which can be readily welded to other weldable steel. With its low carbon equivalent, it possesses good cold-forming properties. The plate is produced by fully killed steel process . and supplied in normalized or controlled rolling condition. S235J2 Application

Reply

Structural Steels S235, S275, S355, S420 and Their Properties

Structural steels are ferrous metals that belong to the group of mild steels.In this post we’ll cover the uses, mechanical properties and chemical composition of the

Reply

S275J2 Steel Grade, Mechanical Properties, Chemical

S275J2 Steel Grade, Mechanical Properties, Chemical Composition, Grade Equivalent. StandardEN 10025-2:2004, European standard for hot-rolled structural steel. Part 2 - Technical delivery conditions for non-alloy structural steels. Steel gradeS275J2 ; Number1.0145 . The table below show the mechanical properties of grade S275J2

Reply

S235JR Non-alloy quality structural steel

Jul 12, 2018 · Mechanical Properties of S235JR SteelsFollowing are some of the mechanical properties of 1.0038 steelsThe tensile strength of the S235JR non-alloy steel is eed in Newton per millimeters and it should be in the range of 360 to 510 N/mm2 (MPa).

Reply

EN 10025-2 Grade S355J2 normalized or normalized formed

The hot rolled, unalloyed quality steel S355J2 is a higher strength fine grained steel for dynamic loaded welding constructions. Dimensioning advantages in respect to the S235J2 due to the by 120 MPa higher yield strength. The steel shows a by 15% higher resistance to mineral wear due to sliding action in comparison to S235J2.

Reply

S235JR Non-alloy quality structural steel

Jul 12, 2018 · Mechanical Properties of S235JR SteelsFollowing are some of the mechanical properties of 1.0038 steelsThe tensile strength of the S235JR non-alloy steel is eed in Newton per millimeters and it should be in the range of 360 to 510 N/mm2 (MPa).

Reply

S235J2,S235J2 STEEL,S235J2 PLATE

Low temperature impacting test shall be done for structural steel plate S235J2 under minus 20 centigrade.When rolling of steel plate S235J2,As rolled or Normalizing rolling is both ok.As rolled delivery condition without any special rolling and heat treatment condition.Normalizing rolling process in which the final deformation is carried out in

Reply

S355J2 steel, S355J2 steel Equivalent grade - Steel

S355J2 steel is not ideally suited to hardening, though S355J2 steel can be subjected to limited heat treatment process such as case hardening. If hardening S355J2 steel heat treatment temperatures, including rate of heating, cooling and soaking times will vary due to factors such as the shape and size of each component.

Reply

S235J2G3 - BEBON steel

S235J2G3 steel plate, EN10025 S235J2G3 steel plate is a kind of carbon structural steel. EN10025 S235J2G3 steel plate is characterised by a minimum yield strength of 170-235MPa and tensile strength of 340-510MPa,so S235J2G3 steel is mainly used in riveted, bolted, or welded construction of bridges and buildings.The following are EN10025

Reply

S235 Structural Steel Plate, S235JR Structural Steel Plate

SAILMA 250HI Structural Steel Plate, S235 Structural High Tensile Steel Plates Distributor, ISO E235B Steel Plate Stockist in Mumbai, India. S235J2 Structural Steel Sheets, S235JR Plates, IS 2062 E250 C Sheets Exporter, AFNOR E24-2 structural steel plates Dealer, SAILMA 250 Plate Supplier in India.

Reply

Steel Grade Equivalency Table

Steel Trade Graphs. If you are interested in the past and current steel trade volumes in various steel products around the globe, this section is just for you. Events Events . Events Events Our major market-leading conferences and events offer optimum networking opportunities to all participants while adding great value to their business. Steel

Reply

World Steel Grades Equivalent - US ASTM AISI SAE,

S235J2 Steel (1.0117 Material) The S235J2 steel (1.0117 material) is an non-alloy carbon steel steel grade in accordance with EN 10025-2. Steel S235J2 Meaning "S" stands for structural steel; "235" means the minimum yield strength (MPa) for the steel

Reply

Contact us